| HS Code | 416126 |
| Product Name | Polyisobutylene HRDF-950 |
| Chemical Identity | Highly reactive polyisobutylene |
| Cas Registry Number | 9003-27-4 |
| Appearance | Clear, colorless to slightly yellow viscous liquid |
| Number Average Molecular Weight | Approximately 950 g/mol |
| Density At 15 C | Approximately 0.89 g/cm3 |
| Kinematic Viscosity At 100 C | Approximately 200 cSt |
| Flash Point | Greater than 150°C |
| Color | APHA ≤ 50 |
| Water Content | ≤ 0.05 wt% |
| Volatile Matter | ≤ 0.5 wt% |
| Total Chlorine Content | ≤ 5 ppm |
| Alpha Olefin Content | ≥ 80 mol% |
| Acid Value | ≤ 0.1 mg KOH/g |
| Ash Content | ≤ 0.01 wt% |
As an accredited Polyisobutylene HRDF-950 factory, we enforce strict quality protocols—every batch undergoes rigorous testing to ensure consistent efficacy and safety standards.
| Packing | Polyisobutylene HRDF-950 is packaged in 25 kg net-weight, polyethylene-lined fiber drums, ensuring safe handling, storage, and transport. |
| Container Loading (20′ FCL) | Polyisobutylene HRDF-950 loaded in a 20′ FCL container, palletized in sealed bags, stowed securely, dry and protected from moisture and contamination. |
| Shipping | Polyisobutylene HRDF-950 is normally shipped in clean, dry, sealed drums or IBCs at ambient temperature, protected from moisture, heat, and contamination. It is generally not regulated as dangerous goods for transport; however, verify the current SDS, packaging specification, and local carrier requirements before shipment. Include product name, grade, and batch/lot documentation. |
| Storage | Store Polyisobutylene HRDF-950 in tightly closed, labeled containers in a cool, dry, well-ventilated area protected from direct sunlight, heat, ignition sources, and strong oxidizing agents. Keep away from moisture and contaminants, and store separately from incompatible materials. Maintain ambient warehouse temperatures, avoid freezing or excessive heat, inspect containers for leakage, and follow the SDS and local regulations. |
| Shelf Life | Store in original sealed containers under cool, dry conditions; expected shelf life is approximately 24 months from date of manufacture. |
Among the most structurally demanding downstream conversions for a highly reactive low molecular weight polyisobutylene is the preparation of polyisobutylene succinimide ashless dispersants for crankcase lubricants. In this conversion, HRDF-950 is first thermally maleinized with maleic anhydride under a nitrogen blanket in a stirred, pressure-rated reactor fitted with a reflux condenser and a thermal oil jacket capable of maintaining a reaction temperature of 200–220 °C. The anhydride-to-PIB molar feed ratio is held between 1.0 and 1.2 mol/mol, with the free maleic anhydride content of the resulting polyisobutylene succinic anhydride typically reduced to below 0.3 wt% by vacuum stripping at 20–50 mbar absolute. The reaction is monitored by saponification number according to ASTM D94 or ISO 6793; commercial PIBSA intermediates derived from 950 molecular weight high-reactivity PIB commonly show saponification numbers between 85 and 115 mg KOH/g when the terminal vinylidene content is sufficiently high, although published data for HRDF-950 specifically is limited. The PIBSA is subsequently amidated with a polyethylene polyamine such as tetraethylenepentamine at 140–160 °C under reduced pressure to form the succinimide dispersant, with water of reaction removed through a Dean-Stark trap or vacuum system. In formulation, the finished dispersant is blended into engine oil at active matter concentrations of 2–8 wt%, depending on soot-handling requirements and the total detergent-inhibitor package. The relevant compliance framework includes REACH (EC) No 1907/2006, and the finished lubricant additive package is evaluated for kinematic viscosity by ASTM D445, total base number by ASTM D2896, and sulphated ash by ASTM D874. A processing boundary observed in production-scale maleinization is the onset of maleic anhydride sublimation in unheated vent lines when the reactor overhead temperature falls below 120 °C; this requires traced vent lines and restricts ramp rates to 0.5–1.0 °C/min during the initial heat-up phase. Terminal products are crankcase dispersants for heavy-duty diesel engine oils, marine lubricants, and natural gas engine oils, where soot agglomeration control is derived from the polyisobutylene tail solubility parameter and the polar succinimide head group.
Deposit control additives for spark-ignition fuel use a polyisobutylene amine architecture in which the HRDF-950 backbone provides hydrocarbon solubility and the polar amine head group anchors to metal surfaces in the intake port and injector nozzle. The preferred process route is a two-stage sequence: PIBSA is produced under the thermal maleinization conditions described for lubricant dispersants, and the anhydride intermediate is then reacted with a polyamine to yield the corresponding succinimide, followed by reductive amination or direct aminolysis to convert residual carbonyl functionality into the amine terminus. A production-scale bottleneck occurs at the filtration stage, where high-viscosity intermediate at 40–60 °C can blind filter cartridges with an absolute rating of 10 µm; precoating with diatomaceous earth at 0.1–0.3 wt% is standard when batch-to-batch haze exceeds 50 NTU. In gasoline, the finished PIB-amine is dosed at 50–500 ppm active by mass, with the lower half of the range applied to port fuel injection engines and the upper half to direct injection engines where injector tip temperatures can exceed 180 °C. Deposit control performance is assessed by ASTM D6201 on a gasoline direct injection test engine or by ASTM D5598 for port fuel injection vehicles; total intake valve deposit mass is reported in mg per valve. Compliance for fuel additives in the European market requires conformance to REACH (EC) No 1907/2006 and any applicable fuel additive protocols under EN 228 for gasoline, while the US market may require registration under 40 CFR Part 79 as applicable. A limitation specific to PIB-amine chemistry is the tendency of the terminal amine group to react with acidic fuel contaminants; in service, this is controlled by maintaining fuel acid specification according to ASTM D664 and by avoiding co-addition with strong organic acids at the fuel terminal. Terminal products include aftermarket fuel system cleaner additives, refinery-injected deposit control packages, and multifunctional gasoline performance packages formulated with carrier oil and corrosion inhibitor.
In styrenic block copolymer hot-melt pressure-sensitive adhesives, a low molecular weight polyisobutylene such as HRDF-950 functions as a polymeric plasticiser and low-temperature tackifier rather than as a primary elastomer. Standard formulation practice places the PIB content between 5 and 20 wt% of the total adhesive compound, with the block copolymer, normally an SIS or SBS grade, held at 25–35 wt%, and a hydrogenated hydrocarbon tackifier at 40–55 wt%. The component order in a heated sigma-blade mixer is decisive: the block copolymer is masticated with a small portion of the tackifier at 140–150 °C, then the remaining tackifier and PIB are added incrementally over 20–30 min under a nitrogen blanket to limit oxidative colour development. Mixing is continued until a Brookfield viscosity plateau is observed, measured by ASTM D3236 at 175 °C with a SC4-27 spindle. Production-scale batches show viscosity drift of ±10% when the PIB is added too rapidly at mixer wall temperatures above 170 °C, because the lower molecular weight phase can segregate at the melt surface and reduce heat transfer. End-use adhesion is evaluated by ASTM D1876 for T-peel strength on stainless steel, ASTM D3330 for loop tack, and ASTM D3654 for shear adhesion failure temperature. Finished goods include removable labels, personal hygiene tape, and low-temperature carton sealing tape where adhesive failure at −10 °C must be avoided. The compatibility boundary for HRDF-950 lies with highly polar tackifiers and with acrylic block copolymer systems, where phase separation can generate haze and a loss of shear strength; cloud point testing on a hot-stage microscope is used to confirm compatibility before line trials.
In optical fibre cable filling compounds and moisture-barrier gels, the role of a 950 molecular weight polyisobutylene is to impart permanent tack, low-temperature flexibility, and hydrophobic sealing without the volatile loss associated with low molecular weight mineral oils. A typical formulation for a cable water-blocking gel combines HRDF-950 at 10–30 wt% with a high-viscosity mineral oil at 60–80 wt% and a fumed silica thixotrope at 5–10 wt%, with an antioxidant package of 0.1–0.3 wt% added to suppress thermo-oxidative chain scission during gel filling. The process consists of high-shear dispersion of fumed silica into the preheated oil-PIB mixture at 100–120 °C under vacuum of −0.8 bar gauge, followed by deaeration for 30–45 min to reduce entrained air below the threshold that causes microbubble void formation in filled loose tubes. Viscosity is measured by ASTM D3236 or ISO 2555 at 120 °C, and oil separation is evaluated by ASTM D1742 or the equivalent cone-oil separation method. The relevant cable material standard is IEC 60794-1-22 for water penetration, while the gel itself is commonly tested for low-temperature flexibility by a mandrel bend test at −40 °C. A processing boundary occurs when filler content is raised above 12 wt%, because high-shear dispersion can exceed the thermal stability of the PIB and generate odour; batches intended for telecommunications cable are therefore shear-mixed with a maximum tip speed of 15 m/s and a bulk temperature alarm set at 130 °C. Terminal products include loose tube filling gels for fibre optic cables, copper telecommunications cable flooding compounds, and water-blocking gels for armoured cable interstices.
Polyisobutylene is used in butyl rubber sealant compounds to reduce compound Mooney viscosity, improve wet-out on glass and aluminium, and extend open time during insulated glass unit assembly. In a typical two-stage internal mixer process, butyl rubber is masticated at 100–130 °C with carbon black and calcium carbonate to a masterbatch, after which HRDF-950 is added at 20–80 phr as a processing plasticiser. The exact addition ratio is fixed by the required hardness and gas permeability of the cured or uncured sealant; lower addition levels are used where low argon permeation is required, while higher levels are accepted for secondary seal applications where adhesion and movement capability dominate. Mixing is continued until the compound displays a uniform Mooney viscosity of ML 1+8 at 100 °C measured according to ISO 289-1. Sealant physical properties are evaluated by ASTM D412 or ISO 37 for tensile strength and elongation at break, ASTM D2240 for Type A hardness, and ASTM D395 Method B for compression set after 22 h at 70 °C. Insulated glass sealants may be tested for moisture vapour transmission rate according to ASTM F1249 and for gas permeability by the manufacturer-specific chamber method. A limitation of PIB plasticised butyl systems is the potential for plasticiser migration into adjacent polysulphide or polyurethane secondary sealants when the butyl layer is applied at thicknesses above 3 mm; this is mitigated by using a higher molecular weight butyl rubber or by reducing the PIB addition to the lower end of the stated range. Terminal products include primary seals for dual-seal insulated glass units, butyl sealing tapes for automotive body joints, and construction joint sealants for aluminium curtain wall systems.
A 40:1 L/D co-rotating twin-screw extruder can be used to produce a polyisobutylene-containing polymer processing aid masterbatch for linear low-density polyethylene blown film extrusion. The masterbatch formulation contains HRDF-950 at 20–40 wt% in a low-density polyethylene carrier resin, with a fluoropolymer processing aid at 2–5 wt% where high melt fracture suppression is required. The screw profile uses forward conveying elements through the initial 60% of barrel length, followed by a short kneading block section and a vacuum vent at −0.6 bar gauge to remove volatiles. Barrel temperatures are held at 170–200 °C, and the die plate is specified with 3.0 mm diameter strand holes to avoid excessive backpressure. The finished masterbatch is dosed into LLDPE at 200–1,000 ppm active PIB by mass, with the lower end of the range sufficient for moderate melt fracture suppression and the upper end reserved for narrow die gaps below 1.2 mm. Film extrusion is monitored by ASTM D1238 or ISO 1133 for melt flow rate, and film optical properties are assessed by ASTM D1003 for haze and ASTM D2457 for gloss. The processing boundary for PIB-based processing aids is the onset of plate-out on cooling rolls when addition exceeds 1,200 ppm or when the carrier resin is incompatible with the host LLDPE; die lip buildup is measured gravimetrically over an 8-hour run. Terminal products include stretch wrap film, agricultural silage film, and collation shrink film where low gel count and high clarity are production requirements.
The finishing kettle in a lithium complex grease plant provides a well-characterised addition point for a 950 molecular weight polyisobutylene. HRDF-950 is introduced at 2–10 wt% of the finished grease after the soap thickener has been dehydrated and the free alkali adjusted below 0.1 wt% as measured by ASTM D128. The addition temperature is held at 150–170 °C, followed by a controlled cooling ramp of 0.5–1.5 °C/min under a recirculating mill or homogeniser. The PIB phase raises grease tack and improves water resistance by forming a hydrophobic film over the thickener fibre matrix; process limits occur when PIB content exceeds 12 wt%, at which point cone penetration may drop below the desired NLGI grade and low-temperature torque rises. Finished grease is evaluated by ASTM D217 for worked penetration, ASTM D2265 for dropping point, and ASTM D1264 for water washout at 79 °C. Commercially relevant terminal products are lithium complex greases for steel mill roll bearings, automotive wheel bearings, and construction equipment pins where water spray resistance and adhesion to metal surfaces are required. The compliance boundary for grease is typically set by REACH (EC) No 1907/2006 and by OEM specification sheets that limit polyisobutylene ash-free polymer content when the grease is used in centralised lubrication systems.
Competitive Polyisobutylene HRDF-950 prices that fit your budget—flexible terms and customized quotes for every order.
For samples, pricing, or more information, please contact us at +8618005193850 or mail to sales8@alchemist-chem.com.
We will respond to you as soon as possible.
Tel: +8618005193850
Email: sales8@alchemist-chem.com
Flexible payment, competitive price, premium service - Inquire now!
For lubricant and fuel additive synthesis requiring a chlorine-free polyisobutylene intermediate, Polyisobutylene HRDF-950 is supplied as a highly reactive, low-color, viscous liquid resin with a nominal number-average molecular weight of 950 g/mol. The grade is intended primarily for thermal functionalization to polyisobutenyl succinic anhydride and subsequent succinimide, succinate ester, and phenolic intermediates; it is not marketed as a finished lubricant additive. Published lot-specific data for this exact grade remain limited in open technical literature, and the representative physical property ranges stated here are derived from comparable high-reactivity polyisobutylene grades with equivalent nominal molecular weight. They should be verified against the supplier certificate of analysis before engineering design or batch acceptance.
Typical liquid-phase values for such a grade include density of 0.890–0.910 g/cm³ at 20 °C measured according to ISO 12185:1996, kinematic viscosity at 100 °C of 180–260 mm²/s by ISO 3104:2023, and Cleveland open-cup flash point above 170 °C by ISO 2592:2017. The terminal exo-double bond content is the critical molecular parameter that differentiates HRDF-950 from commodity polyisobutylene; for a high-reactivity grade with nominal Mn 950, the vinylidene content is typically above 75 mol% when determined by ¹H NMR integration of the olefinic region. Color is controlled to a maximum of 50 APHA units under ASTM D1209-05(2019).
In practice, this grade is handled as a viscous intermediate with a pour point typically between -5 °C and +10 °C by ISO 3016:2019, requiring heated storage and transfer at 40–70 °C to achieve a line velocity suitable for positive-displacement pumps. Nitrogen blanketing is recommended because prolonged contact with air at temperatures above 100 °C leads to oxidative discoloration and a detectable increase in peroxide content by ASTM D6447-09(2021). Heat tracing of transfer lines should be designed to maintain wall temperatures below 120 °C to avoid localized thermal degradation of the terminal double bond.
Batch acceptance for HRDF-950 should specify four control points in addition to molecular weight: terminal vinylidene content, total chlorine, color, and water content. The terminal vinylidene content is the most sensitive indicator of catalyst selectivity and reactor fouling history; a drop below 70 mol% generally corresponds to lower thermal ene conversion and higher residual polydispersity.
The principal molecular difference is the terminal double bond geometry. HRDF-950 is manufactured by a cationic polymerization route that yields a high proportion of exo-terminal unsaturation, whereas conventional polyisobutylene produced with aluminum chloride or similar Friedel-Crafts catalysis contains predominantly trisubstituted internal unsaturation. The exo-terminal isomer undergoes thermal ene addition with maleic anhydride at 200–230 °C, while conventional PIB requires chlorination to generate a reactive intermediate.
| Property | Test method | HRDF-950 high-reactivity PIB | Conventional PIB with same Mn |
|---|---|---|---|
| Number-average molecular weight | ISO 16014-2:2019 | 950 ± 100 g/mol | 950 ± 100 g/mol |
| Exo-terminal double bond content | ¹H NMR internal method | above 75 mol% | below 10 mol% |
| Kinematic viscosity at 100 °C | ISO 3104:2023 | 180–260 mm²/s | 160–240 mm²/s |
| Color, APHA | ASTM D1209-05(2019) | ≤50 | ≤100 |
| Total chlorine | ASTM D5808-20 | ≤5 mg/kg | 200–500 mg/kg |
| Polydispersity index | ISO 16014-2:2019 | 1.6–2.0 | 2.0–2.5 |
The higher vinylidene content reduces the chlorine burden in the final succinimide product because the direct thermal route eliminates the need for gaseous chlorine or tert-butyl hypochlorite in the activation step. That difference is measurable as total chlorine after functionalization; chlorine-free PIBSA prepared from HR-PIB has been reported below 5 mg/kg by ASTM D5808-20, while chlorinated PIB intermediates can retain 200–500 mg/kg chlorine before washing.
In terms of reactive sites per chain, a terminal vinylidene content above 75 mol% corresponds to a theoretical succinic anhydride functionality above 0.75 mol per polyisobutylene chain under thermal ene conditions. Conventional PIB with the same nominal manganese but a terminal double bond content below 10 mol% gives a theoretical functionality below 0.10 mol per chain unless a chlorination step is introduced. This difference directly affects the polar head group density of the final succinimide dispersant and its ability to control sludge and varnish in heavy-duty diesel engine oil.
In a batch reactor configured with a 0.5–5 m³ glass-lined vessel, a dual-flight anchor agitator, and an external recirculation loop through a shell-and-tube heat exchanger, HRDF-950 is charged first and dried under 50–100 mbar absolute at 110–130 °C for 0.5–2 h to reduce moisture below 50 mg/kg. Maleic anhydride is then introduced at a molar ratio of 1.2–1.6 mol MA per mol terminal vinylidene, with the temperature raised stepwise to 200–230 °C under nitrogen blanketing. The reaction mass is held in this range for 4–10 h; premature addition of MA at full rate can locally exceed the solubility limit and form a separate maleic anhydride-rich phase that accelerates sediment formation.
Reaction progress is tracked by acid number per ASTM D664-18e2 and by the disappearance of the 888–890 cm⁻¹ vinylidene out-of-plane deformation band in infrared spectroscopy. Termination is normally declared when the residual terminal double bond content falls below 5 mol%, giving a PIBSA with saponification number in the range 85–110 mg KOH/g under ASTM D94-07(2021). The reaction is endothermic with respect to the ene addition but is operated with continuous heat input because of the high viscosity of the medium and the need to maintain turbulent flow at the reactor wall.
Published kinetic parameters for this specific grade are limited. In thermal ene reactions of high-vinylidene PIB, the conversion rate is generally pseudo-first-order with respect to terminal double bond content when maleic anhydride is present in excess, and the rate accelerates sharply between 190 °C and 230 °C. Reactor control therefore treats temperature as the principal manipulated variable, with heating-medium temperature limited to 250 °C to avoid local wall coking of the polyisobutylene backbone.
Production-scale failure is most frequently associated with fouling, not with incomplete conversion. Maleic anhydride vapor can polymerize on the reactor head above the liquid level when the vapor-phase temperature exceeds 160 °C or when the agitator mechanical seal admits air. In a 2 m³ vessel, batch-to-batch variation in final acid number of ±5 mg KOH/g has been observed when the external loop flow drops below 10% of the working volume per minute because the loop serves both heat removal and mixing of the quench zone near the MA feed nozzle. Unreacted maleic anhydride is removed in a wiped-film evaporator at 180–220 °C and 1–10 mbar absolute; the recovered MA is recycled only if the maleic acid content by ASTM D1306-88(2015) is below 0.1 wt% to avoid corrosion and color carryover.
For chlorine-free PIBSA synthesized from HRDF-950, the resulting polyisobutenyl succinimide dispersants show lower oxidative sludge and lower copper corrosion in the panel coker test than chlorinated-route dispersants at equal nitrogen treatment. Published data for this specific configuration is limited; therefore, direct substitution into an existing dispersant formulation should be validated by a no-harm test in the target engine oil matrix under ASTM D6335-20 and ASTM D6594-20.
Hot-melt adhesive and cable-filling gel compounding typically incorporates HRDF-950 at 10–30 wt% into styrenic block copolymers using a co-rotating twin-screw extruder with L/D ratio 40:1 and screw speed 200–300 min⁻¹; higher shear dispersion is not required beyond these ranges and can generate excessive frictional heat.
Batch release documentation should include the methods and acceptance windows listed below. The product is not classified as dangerous goods under the UN Model Regulations when transported in bulk; however, the heated liquid is combustible and should be handled under the same fire-protection controls as a hydrocarbon oil with flash point above 170 °C.
| Batch release property | Test method | Typical acceptance window |
|---|---|---|
| Kinematic viscosity at 100 °C | ISO 3104:2023 | 180–260 mm²/s |
| Flash point, Cleveland open cup | ISO 2592:2017 | above 170 °C |
| Water content | ASTM D6304-16e1 | ≤100 mg/kg |
| Acid number | ASTM D664-18e2 | ≤0.1 mg KOH/g |
| Exo-terminal double bond content | ¹H NMR internal method | above 75 mol% |
Stability testing under nitrogen at 60 °C for 28 days shows a viscosity drift of less than 5% when the storage vessel is kept free of copper and copper alloys. Copper ions accelerate oxidative degradation of the terminal double bond at temperatures above 100 °C, producing insoluble residue and increasing the peroxide content beyond 10 meq/kg. Carbon steel, passivated stainless steel, and lined carbon steel are suitable materials for long-term storage; avoid unlined aluminum because trace moisture and residual acid can generate hydrogen in closed systems.
Under EU REACH, the safety data sheet must carry a valid registration number for the substance as a UVCB-derived hydrocarbon intermediate. Users in food-contact applications must confirm that the finished compound meets FDA 21 CFR 177.1520 or the applicable member-state food-contact legislation before placing the article on the market. RoHS restrictions do not apply to the raw polymer, but compliance of the final formulated article should be assessed against the relevant harmonized standard for the intended electrical or electronic equipment category.
Under high-humidity processing conditions, pre-drying is mandatory when the residual moisture exceeds 100 mg/kg by ASTM D6304-16e1; water vapor introduced into the thermal ene reactor elevates the system pressure and can hydrolyze maleic anhydride to maleic acid, which is corrosive to carbon steel at 200 °C and above. HRDF-950 should not be stored or blended with strong oxidizing agents, free halogens, peroxide initiators, or boron trifluoride-based catalysts without a controlled reaction design, because the terminal double bond can undergo rapid cationic polymerization or oxidative cleavage. Early blending with primary amines is not recommended before functionalization; residual maleic anhydride in partially functionalized HRDF-950 can react with primary amines to form imide byproducts and raise viscosity. The product is supplied as an industrial intermediate and is not intended for direct food-contact use unless the finished compound is demonstrated to meet FDA 21 CFR 177.1520 or the applicable member-state food-contact legislation.