| HS Code | 336345 |
| Chemical Type | Polyisobutylene |
| Appearance | Colorless to light yellow transparent viscous liquid |
| Molecular Weight Mn | 850 |
| Density 20c | 0.88-0.91 g/cm3 |
| Kinematic Viscosity 100c | 180-220 mm2/s |
| Flash Point Coc | >=180 C |
| Color Apha | <=50 |
| Water Content | <=0.05% |
| Volatile Matter | <=0.5% |
| Acid Value | <=0.05 mg KOH/g |
| Ash Content | <=0.02% |
| Pour Point | <=-30 C |
As an accredited Polyisobutylene HRDF-850 factory, we enforce strict quality protocols—every batch undergoes rigorous testing to ensure consistent efficacy and safety standards.
| Packing | Polyisobutylene HRDF-850 is supplied in 25 kg moisture-resistant bags, palletized and shrink-wrapped for secure industrial transport and storage. |
| Container Loading (20′ FCL) | Polyisobutylene HRDF-850 loaded in original packaging into a 20′ FCL container, securely stowed and braced to prevent movement during transport. |
| Shipping | Polyisobutylene HRDF-850 is typically shipped as a non-hazardous polymer in clean, dry, closed containers. Protect from moisture, contamination, and excessive heat, and store away from strong oxidizers. Follow the SDS and applicable local, national, and international transport regulations. |
| Storage | Store Polyisobutylene HRDF-850 in a cool, dry, well-ventilated area away from direct sunlight, heat, ignition sources, and strong oxidizers. Keep containers tightly closed, sealed, and clearly labeled. Protect from moisture, dust, and contamination. Use original packaging and store at moderate temperature. Avoid spills because the material can be slippery; follow the SDS and local regulations. |
| Shelf Life | Polyisobutylene HRDF-850 has a shelf life of about 24 months when stored unopened in a cool, dry, well-ventilated area, protected from heat, moisture, and sunlight. |
Polyisobutenyl succinic anhydride synthesis from Polyisobutylene HRDF-850 proceeds through a thermal ene reaction rather than the older chlorination route, a distinction that lowers residual chlorine in the finished succinimide dispersant to below 25 mg/kg when the downstream amidation step is properly controlled. In a 10 m³ glass-lined batch reactor fitted with a retreat-curve impeller, internal coil, and nitrogen sparge ring, the HRDF-850 feed is charged with maleic anhydride at a molar ratio of 1.5–2.0:1 maleic anhydride per mole of polyisobutylene. The reaction mass is maintained at 200–230 °C under 0.3–0.5 bar(g) nitrogen for 8–18 h; the terminal vinylidene double bond of the high-reactivity grade permits the thermal ene addition without chlorine, but the conversion is sharply reduced if reactor headspace moisture exceeds 100 ppmv because ring-opening of the anhydride alters the stoichiometry for subsequent amidation. Production-scale failure modes observed on agitated batch lines include localized overheating at wall temperatures above 235 °C, which causes maleic anhydride homopolymerization and a rise in 10 µm bag-filter blocking residue, and loss of agitation during temporary power interruptions, which allows maleic anhydride-rich phase separation and creates hot spots on restart. After reaction, unreacted maleic anhydride is stripped at 10–30 kPa and 215–225 °C; the residual free maleic anhydride is controlled below 0.1 wt% by titration. The HRDF-850-derived PIBSA intermediate then enters amidation with tetraethylenepentamine or equivalent polyamine at an amine/anhydride equivalent ratio of 0.9–1.1, producing succinimide dispersant in which PIBSA-derived content typically comprises 62–78 wt% of the finished dispersant. Regulatory compliance for the PIBSA intermediate is established under REACH registration for CAS 9003-27-4; downstream finished lubricant packages are evaluated against API CK-4 and FA-4 limits, including sulfated ash by ASTM D874, phosphorus by ASTM D4951, total base number by ASTM D2896, and kinematic viscosity by ASTM D445. Finished terminal product types include 15W-40 heavy-duty diesel engine oil meeting CK-4, 10W-30 fuel-efficient FA-4 engine oil, marine trunk piston engine oil, and natural gas engine oil formulations where soot dispersancy and high-temperature deposit control are the primary lubricant performance requirements.
The limiting step is not the initial thermal ene conversion but the removal of residual free maleic anhydride before polyamine addition, because unbound anhydride consumes amine in side reactions and depresses the finished additive’s nitrogen content. For gasoline deposit-control additive production, HRDF-850-derived PIBSA is first dissolved in dearomatized C10–C13 solvent at 60–70 wt% solids and then charged to a stainless steel loop reactor with external heat exchanger. A polyamine such as tetraethylenepentamine or triethylenetetramine is metered at 1.0–1.2 molar equivalents per anhydride equivalent, and imidation is carried out at 150–180 °C for 4–8 h with nitrogen stripping to remove water of reaction. The critical analytical threshold is residual free amine below 0.5 wt%, measured by perchloric acid titration; higher free amine correlates with elastomer seal swelling and thermal instability in the finished gasoline package. HRDF-850-derived PIB-amine detergent is then blended into gasoline additive packages at a neat fuel treat rate of 120–400 mg/kg by mass, with the final dosage dependent on intake valve deposit target and market fuel quality. Regulatory compliance for fuel additive components in the United States is governed by registration under 40 CFR Part 79, while deposit-control performance is demonstrated on a dynamometer using ASTM D6201 for intake valve deposit formation. Downstream production processes at additive plants generally include continuous vacuum stripping of solvent, followed by filtration through 5 µm cartridge filters before blending. Finished product types include port fuel injection gasoline deposit-control packages, direct injection fuel system cleanliness additives, and multifunctional aftermarket fuel additive formulations where the PIB-amine component provides high-temperature valve deposit removal and keep-clean performance in spark-ignition engines.
In dual-sealed insulating glass unit manufacturing, Polyisobutylene HRDF-850 operates as the low-molecular-weight barrier and wetting fraction in a primary sealant formulation, where its gas-barrier contribution depends on both the loading level and the dispersion of carbon black and calcium carbonate fillers. The formulation addition level for HRDF-850 in a hot-applied primary sealant typically falls between 25 wt% and 45 wt% of total compound, with N550 carbon black at 20–35 wt%, calcium carbonate at 10–25 wt%, and processing aids at 1–5 wt%; the higher end of the PIB range is selected when moisture vapour transmission resistance must be maximized for argon-filled units, while the lower end is used for fast extrusion and reduced torque. Downstream production is carried out in a 2,000 L sigma-blade vacuum mixer with jacket temperature 110–150 °C and chamber vacuum 50–100 mbar absolute; mixing continues until a black, void-free mass is discharged through a heated gear pump and slot die. A production-scale failure mode occurs when filler moisture exceeds 0.15 wt% during the mixing cycle, producing microvoids in the edge seal that reduce argon retention and can fail the gas leakage aging test. After discharge, the hot-applied sealant is extruded at 100–130 °C onto aluminium or stainless steel spacer bars, pressed onto glass, and then covered with a secondary polysulfide, polyurethane, or silicone sealant. Regulatory compliance for the insulating glass unit is evaluated under EN 1279-4 for gas leakage and durability, while North American performance is assessed by ASTM E2188 and ASTM E2190; adhesion and cohesive failure of the edge seal are additionally checked by ASTM C794. The finished article types include argon-filled double-glazed insulating glass units, triple-glazed low-emissivity units, and structural glazing edge seals where long-term moisture resistance and low volatile loss are required from the primary PIB sealant.
In styrenic block copolymer hot-melt adhesive formulations based on SIS or SBS polymers, Polyisobutylene HRDF-850 is metered into the feed throat or injection port of a corotating twin-screw extruder with L/D 40:1 and barrel zones set from 120 °C to 180 °C, with screw speed normally maintained between 250 rpm and 400 rpm. The addition level is 5–15 wt% of total adhesive, replacing a similar fraction of conventional low-molecular-weight polybutene or mineral oil; at levels above 15 wt%, shear adhesion failure temperature measured by ASTM D4498 decreases because the PIB phase softens the endblock network. HRDF-850 contributes tack and lowers melt viscosity for slot-die coating and spiral spray application, but its nonpolar structure limits adhesion to polar substrates such as untreated polyester and aluminium; substrate priming or formulation with polar tackifiers is required for those configurations. Downstream processing at converter lines uses hot-melt coaters operating at 150–175 °C, with coating weight for pressure-sensitive tape typically 15–30 g/m². Regulatory compliance for adhesive formulations intended for indirect food-contact applications falls under FDA 21 CFR 175.105 for adhesives, with formulation records required to demonstrate that all components are suitable for the intended contact condition; in the European Union, the relevant framework is Regulation EU 10/2011 for plastic materials and articles intended to come into contact with food, but the final adhesive must be evaluated by the converter for migration limits. The finished terminal product types include pressure-sensitive labels, specialty tape constructions, disposable hygiene article construction adhesives, and removable surface-protection films where controlled peel force and low residue on stainless steel or glass surfaces are required.
For fibre-optic loose-tube cable filling compounds and electrical cable interstitial fillers, HRDF-850 functions as the hydrophobic base fluid that provides low water absorption, controlled low-temperature flexibility, and compatibility with fumed silica thickening agents. The fill compound formulation typically contains 80–92 wt% HRDF-850 as the base fluid, 6–12 wt% fumed silica for yield stress development, and 1–3 wt% styrenic block copolymer or polyethylene wax when additional slump resistance at elevated service temperature is required. Downstream production is carried out in a planetary vacuum mixer at 80–120 °C with a vacuum of 10–20 mbar held for 30–60 min to remove entrained air and residual moisture; the final moisture content is controlled below 50 ppm by Karl Fischer titration before filling. The critical processing threshold occurs during filler addition: excessively fast silica addition or inadequate vacuum generates agglomerates that pass through the cable filling head and cause intermittent buffer tube blockage. After degassing, the gel is transferred to a heated pressure vessel and injected into loose tubes at 70–90 °C, filling the interstices around optical fibres without fibre strain. Regulatory compliance for optical fibre cable filling compounds is assessed under Telcordia GR-20-CORE for generic requirements for optical fiber and cable, with environmental exposure methods described in IEC 60794-1-22; for power cable applications, the filled cable is subject to the relevant cable system test standards such as IEC 60840 or IEEE 48 depending on voltage class. The finished product types include loose-tube fibre-optic cable buffer tube gels, stranded loose-tube cable interstitial fillers, and power cable water-blocking fillers where the polyisobutylene-based compound must remain non-dripping at 70 °C and must not exude low-viscosity oil during thermal cycling.
Polyisobutylene HRDF-850 is added to butyl rubber innerliner and inner tube compounds at 5–12 phr to reduce compound nerve and improve mill flow without increasing sulfur bloom or extractable content in the cured rubber. In a tangential internal mixer of 270 L net chamber volume, the butyl polymer is masticated for 30–45 s, carbon black and processing aids are added, and HRDF-850 is introduced after black incorporation to avoid excessive rotor slip and dispersion loss. The mixed stock is dumped at 130–150 °C and sheeted on a two-roll mill to 3–5 mm thickness; Mooney viscosity measured by ASTM D1646 at ML1+4/100 °C typically falls by 8–15 MU relative to the same compound without the PIB plasticizer. The processing boundary is 12 phr: above this loading, green strength measured by ASTM D6746 declines to a level that causes mill sticking and splitting during innerliner calendering. Compound mixing procedures are validated under ASTM D3182, and cured tensile properties are evaluated by ASTM D412 after vulcanization in a steam autoclave. The finished product types include butyl innertubes, tubeless tire innerliners, and high-temperature curing bladders where low air permeability, good tack, and resistance to oxidative aging are the principal performance criteria for the rubber compound.
Competitive Polyisobutylene HRDF-850 prices that fit your budget—flexible terms and customized quotes for every order.
For samples, pricing, or more information, please contact us at +8618005193850 or mail to sales8@alchemist-chem.com.
We will respond to you as soon as possible.
Tel: +8618005193850
Email: sales8@alchemist-chem.com
Flexible payment, competitive price, premium service - Inquire now!
Polyisobutylene HRDF-850 is a high-reactivity polyisobutylene feedstock supplied as a low-molecular-weight, clear viscous liquid under Chemical Abstracts Service registry number 9003-27-4. The grade designation identifies a dispersant feedstock rather than a finished lubricant additive. Because the producer has not published a complete HRDF-850-specific specification, acceptance decisions are made from the lot certificate of analysis; the values discussed here are representative of the high-reactivity polyisobutylene class and do not replace batch-specific data. The defining structural parameter is the terminal vinylidene content. In high-reactivity PIB grades of this molecular weight range, the terminal vinylidene fraction is typically reported above 70 mol% when measured by an internal Fourier-transform infrared method calibrated against proton nuclear magnetic resonance. Kinematic viscosity at 100 °C for comparable HR-PIB grades commonly falls between 190 mm²/s and 230 mm²/s under ASTM D445, and the number-average molecular weight generally falls between 900 g/mol and 1,100 g/mol by ISO 16014-2 gel permeation chromatography. Dispersity is typically 1.6–2.0.
The terminal vinylidene group is the primary thermal maleation site, and the low residual halogen content is a second specification driver. Field transfer data from heated jacketed lines indicate that viscosity below 60 °C can exceed 1,500 mPa·s, and gear pump suction losses become significant when the product is held below 40 °C. Heated storage at 60–80 °C and continuous nitrogen blanketing are therefore used in production handling systems. Because the product is manufactured by boron trifluoride-catalyzed cationic polymerization, residual catalyst-derived fluorine and chloride are controlled; combustion ion chromatography is used to verify that halogen content remains below the limits in the batch certificate.
The following table lists representative property windows for high-reactivity polyisobutylene grades of similar molecular weight. These ranges are not HRDF-850 lot-release limits unless stated on the manufacturer’s certificate of analysis. All values should be verified against the batch-specific data package supplied with the shipment.
| Parameter | Method | Representative range | Reference note |
|---|---|---|---|
| Kinematic viscosity at 100 °C | ASTM D445 | 190–230 mm²/s | Class-typical value |
| Number-average molecular weight | ISO 16014-2 | 900–1,100 g/mol | Gel permeation chromatography |
| Dispersity Mw/Mn | ISO 16014-2 | 1.6–2.0 | Gel permeation chromatography |
| Terminal vinylidene content | Internal FTIR | >70 mol% | Calibrated against 1H NMR |
| Water content | ASTM D6304 | ≤50 mg/kg | After drying |
| Acid number | ASTM D664 | <0.1 mg KOH/g | As-supplied |
| Chlorine content | Combustion ion chromatography | <30 mg/kg | Typical for BF3-catalyzed HR-PIB |
Molecular weight should not be interpreted by viscosity alone. Two lots with identical ASTM D445 viscosity at 100 °C can differ in number-average molecular weight and terminal vinylidene content because viscosity-average molecular weight is sensitive to the high-molecular-weight tail. For this reason, ISO 16014-2 GPC and FTIR vinylidene measurements are both required for critical dispersant feedstock approval. The FTIR method integrates the absorbance at 895 cm−1 for the terminal vinylidene out-of-plane deformation and compares it to the internal double-bond band near 1,640 cm−1; calibration is performed with proton NMR on the same batch.
For incoming quality control, the terminal vinylidene content should be rechecked when the material has been stored longer than 6 months or when the nitrogen blanket has failed, because exposure to oxygen at elevated storage temperature reduces the reactive end-group concentration. The ASTM D445 viscosity is run at 100 °C to stay within the calibrated range of standard glass capillary viscometers; if a rotational rheometer is used for expedited screening, the shear rate should be specified in the test report because the material is Newtonian only below 1,000 s−1 and above 60 °C.
The viscosity-temperature relationship for HR-PIB of this molecular weight range can be approximated for transfer system design using the practical values at 40 °C and 60 °C. Heated line sizing calculations should use a density near 0.89–0.92 g/cm³ at 60 °C by ASTM D4052 and a specific heat near 2.0–2.2 kJ/(kg·K). These design values correspond to the high-reactivity PIB class; HRDF-850-specific thermophysical data should be pulled from the supplier’s data sheet if available.
Within heavy-duty diesel lubricant dispersant production, HRDF-850 is thermally adducted with maleic anhydride to produce polyisobutenyl succinic anhydride intermediate. The reaction is carried out in stainless steel or glass-lined batch reactors with overhead condensers and inert gas blanketing; the ene reaction is run at 200–230 °C for 8–24 h using a maleic anhydride-to-vinylidene molar charge between 1.2:1 and 1.5:1. Acid number development is tracked by ASTM D664, and the endpoint is reached when the free maleic anhydride content falls below 0.5 wt% by hot water titration or equivalent. The PIBSA is then vacuum-stripped at 20–50 kPa absolute and reacted with polyethyleneamine bottoms to form succinimide dispersants. HRDF-850 is not directly evaluated by engine tests; instead, the downstream dispersant is screened with soot-thickening bench tests such as ASTM D5967 or ASTM D7156 and then in full engine sequence testing if required by the lubricant specification.
The succinimide dispersant produced from HRDF-850 has a nitrogen content typically 1–2 wt% and total base number below 20 mg KOH/g by ASTM D2896, depending on the amine ratio. The molecular weight of the PIBSA intermediate is kept low enough to prevent viscosity index improver conflict in the finished engine oil.
A second use is as a precursor for fuel detergent polyisobutenyl succinimides and succinamides used in gasoline direct injection deposit control. In this route, the PIBSA is reacted with polyamines in a solvent-free melt at 150–180 °C, and the imidization reaction is followed by acid number reduction and infrared amide/imide carbonyl absorbance. The final fuel additive package is evaluated under ASTM D6201 or ASTM D5599 for intake valve deposit formation, not by PIBSA viscosity alone.
Pre-drying is not required when the water content is below 50 mg/kg by ASTM D6304. If the product has been exposed to humid air above 60% relative humidity, vacuum drying at 80 °C for 2–4 h is sufficient to return the water content to the specified range.
The upper boundary of the thermal maleation window is set by competing double-bond isomerization. At reaction temperatures above 230 °C, terminal vinylidene groups migrate to internal positions and maleic anhydride adduction selectivity declines. Published kinetic data specific to HRDF-850 are limited; process validation is required to establish the selectivity-temperature function for a given reactor. Standard practice places the control band between 200 °C and 230 °C.
At production scale, the ene reaction is exothermic. In a 20,000 L glass-lined reactor with half-pipe jacket cooling, maleic anhydride is normally charged in staged portions over 2–4 h to limit temperature overshoot to below 5–10 °C. A single-shot charge can produce localized anhydride concentration gradients and raise the internal temperature above 240 °C; the resulting color increase and gel formation are observable as filter plugging during discharge. The lower boundary is set by reaction rate. At 180 °C, the thermal ene reaction is slow; residual maleic anhydride after 24 h can exceed 2 wt% unless the anhydride is replenished. The control band therefore represents a balance between conversion and color.
Oxidative degradation is a separate limiting factor. The terminal vinylidene group reacts with oxygen through a radical chain mechanism; initiation is significant at maleation temperatures. Headspace oxygen should be kept below 50 ppm by continuous nitrogen purge, and reactor pressure should be monitored at 10–50 kPa gauge. If oxygen ingress occurs, acid number development may still reach target because maleic anhydride can graft through radical intermediates, but the product color darkens and the dispersant may develop higher sludge entrainment. In-process color is monitored under ASTM D1209, with typical PIBSA color values below 8 units when oxygen is excluded.
Viscosity evolution during maleation creates a rheological constraint. The initial HRDF-850 charge at 100 °C has capillary viscosity in the 190–230 mm²/s range, but the PIBSA intermediate may reach 1,000–2,000 mm²/s at 100 °C depending on degree of maleation and residual polymer. Agitator power draw in a retreat-curve impeller system rises as the batch viscosity increases; mixing should be maintained above 30 rpm to avoid stagnant zones near the jacket. If the reactor uses a turbine impeller instead of a large-diameter anchor, poor top-to-bottom turnover can create temperature stratification exceeding 5 °C. These limits are engineering control bands reported for high-reactivity PIB maleation; HRDF-850-specific kinetic and rheological data must be established by plant trials.
Scale-up from laboratory glassware is not linear. Laboratory glassware with magnetic stirring under nitrogen can yield a clean maleation in 8 h because heat and mass transfer are efficient. Pilot-plant reactors of 200 L with glass-lined walls and anchor agitators show longer induction periods and wider batch-to-batch variation in acid number endpoint. Production plants therefore use multiple maleic anhydride dosing points below the liquid surface to prevent localized concentration spikes. The use of a dip tube is preferred over feeding maleic anhydride melt into the vapor space, where it can sublime and condense on cooler nozzles and form plugged solids.
Substitution of HRDF-850 for conventional low-reactivity polyisobutylene changes the maleation route and the resulting intermediate quality. Conventional PIB with low terminal vinylidene content requires chlorination or radical initiator addition to achieve acceptable maleic anhydride addition; HRDF-850’s terminal vinylidene content above 70 mol% permits thermal ene adduction without chlorine-promoted chemistry. This difference reduces residual chlorine in the PIBSA and is relevant for formulations requiring total chlorine below 10 mg/kg in the finished lubricant package when tested by ASTM D808 or combustion ion chromatography.
| Property | HRDF-850 class | Conventional low-reactivity PIB | Method |
|---|---|---|---|
| Terminal vinylidene content | >70 mol% | <10 mol% | Internal FTIR |
| Maleic anhydride adduction route | Thermal ene at 200–230 °C | Chlorine-promoted or radical initiator route | Process observation |
| Residual chlorine | <30 mg/kg | 50–300 mg/kg | Combustion ion chromatography |
| PIBSA color | ASTM D1209 4–8 | ASTM D1209 >10 | Process-dependent |
| Viscosity at 100 °C | 190–230 mm²/s | 180–220 mm²/s | ASTM D445 |
| Dispersant soot handling | Equivalent after succinimide formation | Equivalent after succinimide formation | ASTM D5967 screening required |
The reactivity difference also affects storage stability. Conventional low-reactivity PIB is less sensitive to oxygen, while HRDF-850 should be protected from air during heated storage. Plant transfer systems designed for conventional PIB may not require a pump type change, but insulation and heat tracing on filters and flow meters must be added because the higher terminal vinylidene content does not materially reduce viscosity compared with conventional PIB of the same molecular weight.
Compared with other high-reactivity PIB grades, HRDF-850 is selected by lot-specific terminal vinylidene content and viscosity consistency rather than by brand. Differences between HR-PIB suppliers are most visible in the low-molecular-weight tail and in residual boron content, which can influence downstream filterability of PIBSA. When switching between HR-PIB sources, the PIBSA acid number curve should be revalidated because the vinylidene content distribution across the molecular weight range affects the rate of anhydride addition, not only the average vinylidene value.
HRDF-850 is not directly interchangeable with polybutene plasticizer grades or with butyl rubber in sealant formulations. The product’s low molecular weight and reactive terminal double bond are suited to chemical derivatization, not to cohesive-strength generation in cured elastomer compounds. In sealant or adhesive formulations requiring high-vinylidene PIB as a reactive plasticizer, the addition level is usually below 10 wt%; above that, tensile strength under ISO 37 may decline because the low-molecular-weight fraction dilutes the lightly crosslinked network. Published data for HRDF-850-specific sealant performance are limited.
Bulk storage of HRDF-850 should maintain a dry nitrogen blanket at 20–50 kPa gauge and a storage temperature between 25 °C and 40 °C. Heat-traced lines at 60–80 °C and gear pumps with pressure relief set at 1,000 kPa are common for transfer. The product should be kept away from strong acids, peroxides, and free-radical initiators, which can polymerize the terminal double bond and increase viscosity. Contact with copper or copper alloys above 80 °C should be avoided because copper ions can accelerate oxidative degradation. If storage exceeds 12 months, revalidation of terminal vinylidene content and viscosity under ASTM D445 is necessary before use in dispersant production. The certificate of analysis remains the controlling document for lot acceptance.